






LEER 100XQ Camper Shell – Premium Fiberglass Truck Topper
The LEER 100XQ camper shell sets the industry standard for fiberglass truck toppers, combining aerodynamic styling with proven durability. We engineered this model to deliver a seamless factory appearance on your pickup bed, with OE-quality paint that perfectly matches your truck's finish. The 100XQ features our proprietary reinforced fiberglass construction—lightweight enough to optimize fuel economy yet strong enough to handle years of highway driving, job site demands, and weather extremes.
Every 100XQ we build incorporates exclusive three-point latching hardware and high-density weather seals that keep moisture, dust, and road noise out of your truck bed. The design maintains full bed access through the rear door while adding protected storage capacity for tools, gear, or cargo you need to keep secure and dry.
What Makes the 100XQ Stand Out

Fiberglass Construction & Paint Quality
We hand-lay every LEER 100XQ shell using multiple layers of reinforced fiberglass resin, creating a one-piece molded structure that eliminates weak seams and potential leak points. This manufacturing process produces a shell that weighs approximately 180–220 pounds depending on bed length, light enough for two-person installation yet rigid enough to resist flexing on rough roads.
The paint process mirrors automotive OE standards. Each shell receives multiple primer coats, color-matched base layers, and a UV-resistant clear coat that’s baked in temperature-controlled booths. We match over 200 factory truck colors, and the finish quality is indistinguishable from your truck’s factory panels. The clear coat resists oxidation, chalking, and fading significantly better than gel-coat alternatives common in budget camper shells.

Weatherproofing & Seal Technology
The 100XQ employs a dual-seal system along every mounting surface and door perimeter. High-density EPDM rubber seals compress against the truck bed rail and tailgate, creating a moisture barrier that stays pliable in temperature extremes from –40°F to 140°F. We position the primary seal along the shell’s lower flange and add a secondary bulb seal that contacts the bed rail’s vertical surface.
Rear door weatherproofing includes a full-perimeter gasket plus a dedicated rain gutter molded into the upper shell body. Water channels away from the door opening rather than pooling against the seal. The three-point latching system—one center latch plus two side pull-down latches—applies uniform compression across the entire door frame, eliminating the gaps that appear in single-point systems when seals age.
Installation & Truck Compatibility
We manufacture the 100XQ in bed-length-specific models for 5.5-foot, 6.5-foot, and 8-foot truck beds across Ford, Chevrolet, GMC, Ram, Toyota, and Nissan full-size pickups. Each configuration includes custom-drilled mounting rails that align with your truck’s stake pocket holes or designated mounting points—no drilling into the bed itself is required for most applications.
The aluminum C-channel mounting system clamps over the bed rail, distributing load evenly and allowing for minor adjustments during installation to ensure the shell sits level front-to-back and side-to-side. We include all necessary hardware: stainless steel clamps, nylon isolator pads to prevent paint chipping, and color-matched trim strips that conceal the clamp hardware along the bed rail.



Fiberglass Camper Shells for Every Truck Configuration
Rated 4.8 by verified buyers






Common Questions About the LEER 100XQ
Yes, the 100XQ mounts over most spray-in bedliners without modification. The aluminum C-channel clamps sit on top of the bed rail, and the seal compresses against the liner surface. We recommend professional installation to ensure proper seal compression if your bedliner is thicker than 1/4 inch, as minor clamp adjustments may be needed for optimal weatherproofing.
The 100XQ receives the same multi-stage paint process used in automotive manufacturing: EPDM primer, color-matched basecoat, and UV-resistant clear coat baked at controlled temperatures. We match over 200 OE truck colors using the same paint suppliers that serve major automakers. The finish quality, gloss depth, and durability are equivalent to your truck's factory panels, and the clear coat can be polished and maintained with standard car care products.
Yes, we manufacture specific roof rack systems designed for the 100XQ. These racks use through-bolt mounting into reinforced areas of the fiberglass shell, spreading load across internal support ribs. Our racks are rated for 150–300 pounds depending on configuration. We do not recommend aftermarket racks designed for other shell brands, as mounting points may not align with the 100XQ's internal structure and could crack the fiberglass if improperly installed.
The 100XQ has a traditional cap design where the shell sits on top of the bed rails with visible mounting hardware concealed by trim strips. The 100XL features flush-mount side panels that wrap down over the bed rail, creating a seamless integrated appearance with no visible mounting clamps. Both use identical fiberglass construction and paint quality. The 100XL provides a more aerodynamic profile, while the 100XQ offers slightly easier installation and lower cost.
Clean the EPDM rubber seals every 3–4 months with mild soap and water, then apply a silicone-based seal conditioner to prevent drying and cracking. Inspect the bulb seals along the bed rail for compression set—if they appear permanently flattened, they should be replaced. Check the rear door gasket for tears or separation and verify that all three latch points engage fully. Most seals last 5–7 years with basic maintenance, and replacement seals are available through LEER dealers.
No, the 100XQ requires removal of tonneau cover mounting systems. The shell's C-channel clamps must sit directly on the bed rail surface to achieve proper seal compression and structural integrity. Some customers alternate between a tonneau cover and camper shell seasonally, but this requires removing and reinstalling the respective mounting hardware each time. For customers who need both low-profile and full-height options, we recommend choosing based on your primary use case.
No, the 100XQ rear door is designed to open only when the tailgate is lowered. The door latch engages a striker mounted to the tailgate itself, so the tailgate must be in the down position for the latch to release. This design ensures a tight weatherproof seal and allows the door to use the tailgate's structural support. If you need bed access without lowering the tailgate, consider our models with side-access doors or lift-up window configurations.






