






LEER Locker Storage System – In-Bed Organization for Work & Recreation
Our LEER Locker transforms your truck bed into a rolling workshop with secure, drawer-style compartments that protect tools, fishing tackle, camping equipment, and job-site essentials from weather and theft. Each drawer rides on heavy-duty ball-bearing slides that support up to 200 pounds fully extended, while three-point locking mechanisms keep contents secure when you're away from the vehicle.
We built the locker frame from aluminum with reinforced corner gussets so it can handle constant jobsite use without warping or cracking. Weather seals run the perimeter of each drawer face to keep dust and water out during highway rain or off-road mud. The system mounts directly to your truck bed floor using existing tie-down points—no drilling required—and works under most tonneau covers or with our matching LEER truck caps.
Storage & security specs

Drawer capacity & dimensions
The LEER Locker ships in three main configurations to fit short-bed, standard-bed, and long-bed pickups. Our most popular setup for 5.5-foot beds includes two full-width drawers (each 18 inches deep by 60 inches wide) stacked vertically for a total height of 12 inches. Standard and long-bed kits add a third drawer or extend drawer width to match your bed length.
Each drawer offers approximately 9 cubic feet of enclosed storage when fully closed. We recommend distributing weight evenly across the drawer floor—concentrated loads near the front edge can stress the slide rails during extension. The textured drawer bottoms prevent small items from sliding during transit, and optional foam liners add cushioning for delicate electronics or camera gear.

Installation & truck bed compatibility
Mounting the system
Installation takes about 45 minutes with basic hand tools. The locker frame includes adjustable mounting brackets that hook into your truck’s factory bed tie-down slots, eliminating the need to drill holes in the bed floor. Once positioned, you tighten four carriage bolts per bracket to lock the frame in place.
We designed the system to sit low enough that most roll-up and folding tonneau covers close without interference. The 12-inch stacked height leaves 8-10 inches of vertical clearance in a typical truck bed, so you can still haul lumber or kayaks above the locker. Pairing the drawers with a LEER 100XL truck cap creates a fully enclosed cargo area where the locker drawers remain accessible from the tailgate while tools stay protected under the cap’s locking side windows.
Security features & keyed cylinders
Each drawer uses a three-point locking rod that engages the frame at the top, middle, and bottom of the drawer face when you turn the key. This distributed locking prevents prying attacks that target single-latch designs. All cylinders on a single locker system use the same key, and we offer keyed-alike options if you’re outfitting a fleet so one master key opens every truck.
The lock cylinders are automotive-grade with hardened steel pins that resist drilling and picking. Weather boots cover each cylinder to keep moisture and dirt out of the tumbler mechanism. If a key is lost, replacement cylinders are available through LEER dealers using your original lock code, which we keep on file for the life of the product.



More LEER truck bed solutions
Rated 4.8 by verified buyers





Common questions about the LEER Locker system
Most truck owners complete the installation in 45 minutes to an hour using basic hand tools like a socket wrench and an adjustable wrench. The system uses your truck's factory bed tie-down slots, so no drilling is required. We include detailed instructions with each kit, and LEER dealers offer installation services if you prefer professional mounting. The hardest part is usually positioning the frame level before tightening the carriage bolts—a second person makes that step easier.
The LEER Locker measures 12 inches tall when the drawers are stacked, leaving 8-10 inches of vertical clearance in most truck beds. Roll-up, folding, and retractable tonneau covers typically close without interference. Hard one-piece covers may require removal or adjustment depending on their mounting height. If you have a LEER truck cap, the locker drawers remain fully accessible from the tailgate and the cap's side windows provide additional entry points for gear stored above the drawers.
Each drawer is rated to support 200 pounds when fully extended on the ball-bearing slides. We recommend distributing weight evenly across the drawer floor rather than concentrating heavy items near the front edge, which can stress the slide rails. For daily use, most people load 80-120 pounds per drawer—tools, tackle, camping gear, or work supplies—without issue. The aluminum frame itself can handle the combined weight of all drawers loaded to capacity.
The LEER Locker uses compression weather seals around each drawer face to block rain, dust, and road spray during normal driving conditions. The seals keep contents dry through car washes and highway rainstorms, but the system is not submersible or designed for standing water. If you routinely ford deep water or park in flood-prone areas, store sensitive electronics in waterproof cases inside the drawers as an extra precaution.
Yes, we offer keyed-alike and master-key options for fleet customers. When you order multiple locker systems, specify keyed-alike on your order and all cylinders will use the same key. LEER dealers can also rekey existing lockers to match your fleet's master key system. We keep lock codes on file so replacement cylinders can be ordered if keys are lost.
We manufacture locker kits for short beds (5.5 feet), standard beds (6.5 feet), and long beds (8 feet) across most major truck brands including Ford, Chevrolet, GMC, Ram, Toyota, and Nissan. Each kit includes adjustable mounting brackets to accommodate slight variations in bed width and tie-down spacing. Measure your bed length and check the compatibility chart on our dealer site or call a LEER dealer to confirm the correct kit for your truck model and year.
The locker frame is designed to mount toward the front or sides of the bed, leaving the center and rear areas open for spare tire access in most trucks. If your spare is stored under the bed, you can access the hoist mechanism from the tailgate as usual. For in-bed spare configurations, position the locker drawers along one side of the bed to maintain clearance. Our installation manual includes bed layout diagrams showing recommended placement for various truck models.




